Home » Tips » How to Hide LED Strip Light Wires

How to Hide LED Strip Light Wires

As an Amazon Associate we earn from qualifying purchases.

Are those protruding wires left behind after installing LED lights giving you sleepless nights? You can easily hide them to give your room a tidier look. If you have no idea how to do this, don’t worry. We have prepared a special guide on how to hide LED strip light wires.

How To Hide LED Strip Light Wires

Hanging wires and cables make a room look messy and it can be dangerous when they’re closer to the floor or pathways. Therefore, it is vital that after you install LED strip lights, you hide these wires to keep your room tidy and hazard-free.

Below are different methods you can use to hide LED strip wires.

Living room with well hidden LED strip light wires

Method 1: Using Panel End Cap and Wall Tape

The panel end caps are super easy to install and provide a quick way of concealing and managing your LED strip light wires.

What You Need 

  • Panel End Cap
  • Double-sided wall tape
  • Tape Measure 
  • Razor Blade

Step One: Measure and Resize the Panel

Panels come from different manufactures and have a standard length of 8ft. Therefore, you will need to measure the size of the path you want your wires to follow, both straight sites and inside cabinets. 

Cut the panel end cap to fit. The length and number of panels you need depend on the number of bends in your wall and the size before each angle.

Step Two: Apply One Side of the Tape on the Panel

Lay down the panel end cap and apply one side of the double-sided wall tape at the back. Try to keep the edge even with the curve in front, which is the molding’s finished edge. 

If you are using the three-quarter-inch or larger double sidewall tape, you will need to trim the edges to your panel’s size to get a fished molding. The half-inch tapes do not need any trimming, though. However, we recommend the three-quarter-inch double-sided wall tapes because they are versatile, and you can use them on other applications. 

Step Three: Mount Your Panel On The Wall

Pill the cover on the other side of the tapes and carefully stick it on the wall at the right angle to make your work organized. You can use a protractor or leveler to determine the slope against your wall. 

Step Four: Fit The Wire Inside The Panel

Slide the wires inside the gaps. You can use a blunt screwdriver or pen to push them further inside the tray. Be careful not to prick holes or accidentally strip the wires. 

The best wire to use is size 22 because it fit better on the trays. You can also use the small size or larger wires since they are just as good.

Method 2: Using Molding Plastic Or Wood Trays

Plastic moldings come in various shapes that are easy to trim with a razor blade. You only need a few art and craft skills to do this. 

What You Need 

  • Plastic molding
  • Razor Blade 
  • Drill 
  • Nails
LED strip lights

Step One: Mold The Edges

Use a sharp razor blade to carefully mold the plastic’s corner edge to the rights size that will fit your cables. If you are not good at molding, you can buy two outside corner moldings and put them on either side. The layout will give you a nice gap in between to run your wires down. 

Step Two: Measure the Length and Cut the Tray into Appropriate Pieces

First, you will want to measure and cut the trays to run seamlessly along the walls.  You can pre-drill holes on the molding so that you do not accidentally drill through the cables while doing the wall mount. 

Step Three: Mount The Molding Trim And Pass The Wires

Mount your molding onto the wall and secure them by nailing the pre-drilled holes. Pass the wires through the gap between the plastic or wood from one end to the other. 

Method 3: Using Glue and Gun

There are two ways you can do this:

If you apply the glue directly to the wire, you will have to hold it in place when gluing it up and as the glue dries to form the adhesiveness.

Both the glue and the wire are always visible, so it is not right in exposed areas where the cables will be conspicuously visible.  You can apply this method inside cabinets or when your wires follow a hidden path. 

If you are using the second method, follow these simple steps.

Step One: Find The Correct Measurement

Measure the length of the path you want your wires to follow and cut your wire management trays to size as per the measurements. 

Step Two: Mount the Trays On the Wall

You can use nails or a glue gun to stick the sections of your wire management tray on the wall. Check the angle to have an organized pattern.

Step Three: Pass the Wires Inside the Tray

Carefully run your wires through the tray as you glue it into the tray wall. You will have to deal with a small section at a time to allow it to stick.

Other Ways You Can Use To Hide Your LED Strip Wires

Below are more methods you can use to hide your LED Strip wires.

Using Hizze Plates

Hizze plates come in different sizes and types: Those that have clips around them and those that have holes around them.  The disadvantage with the clipped ones is that they are not versatile enough, and you will have to get a perfect size. 

On the other hand, the zip tie plates are versatile, yet you need holes to tie them through or wrap them around to secure the wires

Lighted cabinets

Using Wire Nails

Wire nails have become the most common items in securing wires on the walls or cabinets.  They come in different sizes, so you will need to find the right size for the right cable thickness. 

Some are more versatile than others. If you are not sure of your cables’ consistency, we recommend the plastic one because you can always trim them to size. 

Using Traditional Wire Trays

Traditional wire trays are perfect except that most of them are for AC wires, so they tend to be extra large and bulky. While they can help in hiding the wires, you may not find them attractive with LED strip light cables. 

How Do You Hide Your LED Strip Lights?

Hiding your LED strip lights in the first place will save you the frustration of having to hide the wires later. There are several ways to disguise your LED strip lights to avoid the direct rays while setting the ambient vanish in the environment, as discussed below. 

Placing Your LED Strip Lights At The Bottom Of Your Cabinet Counters

LED strip lights provide that extra glow to your counters that come in handy when cooking or baking. You can also install LED strips along the sides and width of your kitchen cabinet. 

The length of the LED thread you choose for this purpose will depend on how big your kitchen is and, to some extent, the size of your cabinets. You can buy the 16.40 feet long Roll and size it down to the ideal length you need. With this extra glow in your kitchen, you can enjoy more cooking your favorite turkey.

Place Your LED On Top Of Floor Trim Molding To Light Up Your Rooms

This method first requires you to install the LED strips then use a skirting board to hide them. The board should be taller than your trim molding. 

You can use wood glue to the board’s edges and line it up just below the LED strip to prevent the sharp light flush from hitting your floor. You must hold the board in position for about 30 seconds to ensure it sticks together. 

This way, your LED lights will be hidden behind the floor molding and above the skirting board and will light up your wall. The glow is even better with RGB LED strip lights because of the color variations.  The length of the LED you will need to buy will depend on how many rooms you want to light and how big each room is.  

Run your LED Light Strip Around your Mirror to Create a Perfect Glowing Vanity

In this case, your mirror should be about 9.8 mm wide. Placing an LED light strip around it illuminates well-lit vanity, which helps you wear that make-up or do your hair. 

Install your LED Lights Strips at the Back Of Your TV, Entertainment Unit, Or on the Wall Behind Your TV

Doing this will introduce the backlit effects, illuminate your entertainment area, and create an ambient mood in the room. Here the length of the LED will depend on the size of your TV. For smaller TVs, we recommend that you buy the 1 m or 3m LED thread. However,  for the larger sizes, a 5 meters LED strip or longer will be ideal. 

Hide your LED at the Bottom of Your Bed to Set an Ambient Tone

You can give your bedroom a calm and relaxing atmosphere by installing the RGB LED light under the bed. The best bed frame for this purpose should be 9.9 mm wide, and a 10 m roll of the LED strip should be enough depending on the width and length of the bed. 


Hopefully, after reading this article, you now know how to hide the LED strip light cables that have been bothering you. You have also learned where you can hide your LED  for a disguising, well lit ambient, and mood for every room in your house. You might want to try this on your workstation, placing it behind the garland, or hiding it under your sturdy pool table, which may give you a good mood all the time.