Home » Tips » Can You Cut Govee LED Lights?

Can You Cut Govee LED Lights?

As an Amazon Associate we earn from qualifying purchases.

LED lights are one of the most interesting ways to light up and decorate a space. While cutting along a straight line may seem simple, you would be surprised at the number of people who destroy good strips. So can you cut Govee LED lights? Let’s find out.

Can You Cut Govee LED Lights?

Yes, you can cut most Govee LED lights. Most Govee LED strip clearly show cut lines that allow you to achieve straight lines. However, you should cut along the indicated lines. Cutting elsewhere on the strip can make the circuits or the entire strip to stop working.

You can also connect the strip with other extension cords using connector kits or use a soldering iron and wires to solder to the strip directly.

Govee LED lights

Can You Cut LED Lights to Custom Lengths?

The good thing about most LED lights is that you can cut them to custom lengths no matter the type of strips you want. They can also help you remain positive and focused and improve the mood of elderly people.

At regular intervals, you will see dotted black or straight lines throughout each LED light. These are the correct points to cut your LED strips without causing damage since circuits are closed at these places. Note that the cutting lines are different on every LED light, which are usually 3.

So if there are 30 lights per meter, your cutting lines will be after every 10 centimeters. There are also copper soldering pads that create a symmetrical pattern at every side of the black line. The pads help you identify the cutting line correctly.

Will Both Sides Work After Cutting Them?

Yes. Both sides will still work as long as you cut them along the indicated cutting lines. As we pointed out earlier, the cutting lines represent the safest point to interfere with the circuit without damaging it permanently.

Keep in mind that each part between the cutting lines is a circuit on its own. This means it doesn’t matter the cutting line you decide to cut along. The good news is that you won’t create more wastage and you can reuse the second half.

How To Cut Govee LED Lights Safely

Personalizing the length of your LED lights is easy. Here’s a detailed guideline.

  1. Begin by testing your LED strips to ensure they work. Although this seems obvious, it’s good to double-check because soldering or cutting strips can void your warranty.
  2. Next, determine the length of your LED strip. To do this, measure the area where you want to install the strips and ensure you take accurate measurements. Once you are done, choose the cutting point on your light that’s close to this length.
  3. Use a pair of scissors or a sharp knife to cut along the cutting line accurately. Remember that LED lights are made to be cut, so you won’t receive a shock.
  4. Decide how you will connect the light to a power source. Most reels are pre-fitted with a power socket. However, you will have to fit a new socket because cutting the LED light gets rid of it. 
  5. You can either use a strip power source connector or solder a new socket on the light. 
LED strip lights

Is It Possible To Reconnect LED Light That Is Cut Off?

What can you do if you cut the light too short accidentally? Can you reconnect the two pieces or will you have to invest in a new light? LED lights can be reconnected if you cut along the dotted cutting line. 

There are several ways you can use to reconnect the two strip light pieces. The easiest way is to use connectors, which are readily available. They also come in different shapes such as T-tap and right angles. 

How Reconnect Cut LED Lights

Strip connectors are the easiest option because they don’t require tools. Here’s a brief guide:

  1. Begin by cutting the translucent plastic that encloses the copper pads with a knife.
  2. Next, insert the light into the connector and ensure the components match each other. 

The second option is to use old wires and a soldering iron to solder to the strip directly. Follow these steps:

  1. Melt the solder onto the copper dots directly to create a small puddle so that you line up the polarity. 
  2. Line up the red line with the positive mark and the black wire with the negative mark.
  3. Strip ½ an inch of the covering off the end of the wires. To join the frayed ends, twist the end of your wire and then connect the wires to the puddles.
  4. Once you have established a connection, plug your lights into a power source, and ensure they are working. 

How To Troubleshoot LED Lights That Are Not Working

Personalizing the length of your strips may seem simple, however, sometimes mistakes happen. If you notice your strips aren’t working after cutting them, check if the strips are designed to be cut. If they aren’t, the damage can’t be reversed. 

Govee LED lights about to be cut

Cutting such strips can cause permanent damage because they have circuits that run continuously throughout the length. If your light is designed to be cut, ensure you made the cut at the right point. 

Cutting outside of the designated place can destroy the individual circuit. So you may need to trim back to the closest cutting point. Other issues include lining up the polarities incorrectly and voltage drops.

Related Questions

Below are some questions you may find helpful.

Where Do You Cut Govee LED Lights?

When cutting Govee LED lights, only cut between the copper dots on the given cut line. Cutting before or after the copper dots can make the following section to lack electrical conductivity.

Can You Cut Govee DreamColor Lights?

No. You can’t cut Govee DreamColor lights because you can’t attach these lights like other LED lights

Are Govee LED Lights Good?

Yes. Govee LED lights are good because they perform well. They are also easy to install behind a desk or TV. 

Conclusion

LED light strips can be personalized to meet different installation requirements. If you are planning to cut LED lights, follow the steps we have outlined above and you will be amazed at how simple it is to complete this task.